TECAST T EF natural

PA 6 C alternative

add to list
product inquiry
request sample

REQUEST FURTHER PROCESSING OPTIONS

Machined part (partner network)

TECAST T EF natural is an alternative to the conventionally cast TECAST T natural. The semi-finished product, based on PA6C, is manufactured using caprolactam from renewable sources according to the mass balance approach. The use of renewable raw materials is allocated to the product on a calculated basis; a specific, physically measurable bio-based content in the individual semi-finished product cannot be derived from this.

The material exhibits the typical properties of cast PA6C and is particularly suitable for demanding applications due to its good mechanical properties and excellent bearing and wear behavior. Because of its low weight, PA6C is frequently used as a replacement for metals and also offers advantages over metallic materials in maintenance applications. Ensinger offers the PA6C bioplastic made from mass-balanced raw material as tubes, plates and rods.

Compared with the corresponding fossil-based variant, TECAST T EF natural has a lower Product Carbon Footprint (PCF). You will find the PCF values and the calculation method in the PCF statement in the download area.

TECAST T EF natural is part of Ensinger's ‘Reuse for Tomorrow’ solutions. These products support the reduced use of fossil raw materials.

 

Facts

Chemical designation
PA 6 C (Cast polyamide 6)
Colour
ivory
Density
1.15 g/cm3

Main Features

  • from biomass-balanced raw materials (details on request, Footprint see PCF statement)
  • good damping
  • good slide and wear properties
  • electrically insulating
  • high strength
  • good wear properties
  • resistant to many oils, greases and fuels
  • high toughness

Target industries

mechanical engineering
food technology
oil and gas industry
automotive industry
heavy duty industry

Downloads

Datasheet (PDF)

Technical details

  • product-technical-detail-collapse-item-0-lvl-1
    Mechanical properties Value Unit Parameter Norm
    Ball indentation hardness 170 MPa ISO 2039-1
    Notched impact strength (Charpy) 4 kJ/m2 max. 7,5J DIN EN ISO 179-1eA
    Impact strength (Charpy) n.b. kJ/m2 max. 7,5J DIN EN ISO 179-1eU
    Compression modulus 2900 MPa 5mm/min, 10 N EN ISO 604
    Modulus of elasticity
    (flexural test)    		 3200 MPa 2mm/min, 10 N DIN EN ISO 178
    Elongation at break (tensile test) 40 % 50mm/min DIN EN ISO 527-2
    Flexural strength 109 MPa 2mm/min, 10 N DIN EN ISO 178
    Elongation at yield (tensile test) 4 % 50mm/min DIN EN ISO 527-2
    Tensile strength 83 MPa 50mm/min DIN EN ISO 527-2
    Modulus of elasticity
    (tensile test)    		 3500 MPa 1mm/min DIN EN ISO 527-2
    Tensile strength at yield 80 MPa 50mm/min DIN EN ISO 527-2
    Shore hardness 83 D DIN EN ISO 868
    Compression strength 19/36/83 MPa 1% / 2% / 5% EN ISO 604
  • product-technical-detail-collapse-item-1-lvl-1
    Thermal properties Value Unit Parameter Norm
    Heat distortion temperature C HDT, Method A ISO-R 75 Method A
    Melting temperature 215 C DIN EN ISO 11357
    Glass transition temperature 40 C DIN EN ISO 11357
    Specific heat 1.7 J/(g*K) ISO 22007-4:2008
    Thermal conductivity 0.38 W/(k*m) ISO 22007-4:2008
    Service temperature 170 C short term NN
    Thermal expansion (CLTE) 12 10-5*1/K 23-60°C, long. DIN EN ISO 11359-1;2
    Thermal expansion (CLTE) 12 10-5*1/K 23-100°C, long. DIN EN ISO 11359-1;2
    Service temperature 100 C long term NN
  • product-technical-detail-collapse-item-2-lvl-1
    Electrical properties Value Unit Parameter Norm
    Dielectric strength kV/mm DIN 53483-1
    volume resistivity 1014 Ω*cm DIN IEC 60093
    surface resistivity 1014 Ω DIN IEC 60093
  • product-technical-detail-collapse-item-3-lvl-1
    Other properties Value Unit Parameter Norm
    Resistance to hot water/ bases (+) - -
    Flammability (UL94) HB - corresponding to DIN IEC 60695-11-10;
    Resistance to weathering - - -
    HZ Brochure for traders yes lbs/in^2 -
    HZ Technical guidelines yes lbs/in^2 -
    HZ-Catalogue yes - -
    HZ Food technology yes - -
    Water absorption 0.2 - 0.4 % 24h / 96h (23°C) DIN EN ISO 62
    Water absorption % saturation (23°C) DIN EN ISO 62

Stock program

Availability
Availability