TECAFORM AH EF natural

POM-C alternative

add to list
product inquiry
request sample

REQUEST FURTHER PROCESSING OPTIONS

Machined part (partner network)

TECAFORM AH EF natural is a POM-C semi-finished product manufactured using renewable raw material sources according to the mass balance approach. The use of these raw materials is allocated to the product on a calculated basis; a specific, physically measurable bio-based content in the individual semi-finished product cannot be derived from this.

As an alternative to conventional POM-C, TECAFORM AH EF natural is suitable for applications in mechanical engineering, food processing technology, and the oil and gas industry. The material exhibits the properties typical of POM-C, including high mechanical strength and stiffness, good wear behavior, low moisture absorption, and high dimensional stability.

Ensinger offers the POM-C bioplastic made from mass-balanced raw material as plates, rods, and tubes. You will find the PCF values and the calculation method in the PCF statement in the download area. Compared with the corresponding fossil-based POM-C variant, TECAFORM AH EF natural has a lower PCF.

TECAFORM AH EF natural is part of Ensinger’s ‘Reuse for Tomorrow’ solutions. These products support the reduced use of fossil raw materials.

Facts

Chemical designation
POM-C (Polyacetal (Copolymer))
Colour
white
Density
1.41 g/cm3

Main Features

  • from bio-based/ biomass-balanced raw materials with optimized PCF
  • high strength
  • resistent to cleaning agents
  • high toughness
  • very good electrical insulation
  • good machinability
  • good slide and wear properties
  • difficult to bond

Target industries

mechanical engineering
automotive industry
aircraft and aerospace technology
electronics
food technology
oil and gas industry

Downloads

Datasheet (PDF)

Technical details

  • product-technical-detail-collapse-item-0-lvl-1
    Mechanical properties Value Unit Parameter Norm
    Tensile strength at yield 67 MPa 50mm/min DIN EN ISO 527-2
    Tensile strength 67 MPa 50mm/min DIN EN ISO 527-2
    Modulus of elasticity
    (tensile test)    		 2800 MPa 1mm/min DIN EN ISO 527-2
    Notched impact strength (Charpy) 8 kJ/m2 max. 7,5J DIN EN ISO 179-1eA
    Elongation at break (tensile test) 32 % 50mm/min DIN EN ISO 527-2
    Flexural strength 91 MPa 2mm/min, 10 N DIN EN ISO 178
    Modulus of elasticity
    (flexural test)    		 2600 MPa 2mm/min, 10 N DIN EN ISO 178
    Ball indentation hardness 165 MPa ISO 2039-1
    Compression modulus 2300 MPa 5mm/min, 10 N EN ISO 604
    Impact strength (Charpy) n.b. kJ/m2 max. 7,5J DIN EN ISO 179-1eU
    Elongation at yield (tensile test) 9 % 50mm/min DIN EN ISO 527-2
    Shore hardness 82 D DIN EN ISO 868
    Compression strength 20/35/68 MPa 1% / 2% / 5% EN ISO 604
  • product-technical-detail-collapse-item-1-lvl-1
    Thermal properties Value Unit Parameter Norm
    Glass transition temperature -60 C DIN EN ISO 11357
    Melting temperature 166 C DIN EN ISO 11357
    Thermal conductivity 0.39 W/(k*m) ISO 22007-4:2008
    Specific heat 1.4 J/(g*K) ISO 22007-4:2008
    Heat distortion temperature C HDT, Method A ISO-R 75 Method A
    Thermal expansion (CLTE) 13 10-5*1/K 23-60°C, long. DIN EN ISO 11359-1;2
    Service temperature 140 C short term NN
    Service temperature 100 C long term NN
    Thermal expansion (CLTE) 14 10-5*1/K 23-100°C, long. DIN EN ISO 11359-1;2
  • product-technical-detail-collapse-item-2-lvl-1
    Electrical properties Value Unit Parameter Norm
    surface resistivity 1014 Ω Silver electrode, 23°C, 12% r.h. -
    volume resistivity 1013 Ω*cm Silver electrode, 23°C, 12% r.h. -
    Dielectric strength 49 kV/mm 23°C, 50% r.h. ISO 60243-1
    Resistance to tracking (CTI) 600 V Platin electrode, 23°C, 50% r.h., solvent A DIN EN 60112
  • product-technical-detail-collapse-item-3-lvl-1
    Other properties Value Unit Parameter Norm
    Resistance to hot water/ bases (+) -
    Resistance to weathering - -
    Flammability (UL94) HB corresponding to DIN IEC 60695-11-10;
    HZ-Catalogue yes - -
    HZ Brochure for traders yes lbs/in^2 -
    HZ Technical guidelines yes lbs/in^2 -
    HZ Aerospace Brochure yes - -
    HZ Food technology yes - -
    Water absorption 0.05 - 0.1 % 24h / 96h (23°C) DIN EN ISO 62
    Water absorption % saturation (23°C) DIN EN ISO 62

Stock program

In addition to our standard dimensions, we manufacture customized tubes, rods and hoses precisely to your specifications. Enquire now.
Availability
Availability